Orders ship from the U.S.

XILO Stax F4 Flight Controller
XILO Stax F4 Flight Controller
XILO Stax F4 Flight Controller
XILO Stax F4 Flight Controller

XILO Stax F4 Flight Controller

Regular price
Sold out
Sale price
$29.99
Shipping calculated at checkout.

The Stax F4 Flight Controller continues XILO's tradition of giving you high-quality FPV gear for a low price point. And it couldn't be easier to install and use on your favorite airframe!

Use this flight controller with the ESC of your choice or pair it with the XILO Stax 45A 3-6s 4-in-1 ESC for seamless integration into your quad.

Remove the mess of soldering - and the chance of making a mistake during build time. The Stax plug n' play capability allows you to simply connect the FC with a compatible ESC with the included 8pin harness, simply wire up your motors and accessories, and you are good to go!

The F4 flight controller gives you proven rock solid processing power while the ICM20602 Gyro/Accelerometer (Up to 32KHz) gives accurate gyro information while in use.

The XILO Stax FC has the unique ability to mount XM+ and Crossfire Nano style receivers directly to the FC. This saves space and makes for an overall cleaner build. If you are using a "slammed" style frame, this feature is very handy as the receiver won't add any additional height to your stack.

Another key feature on the Stax FC is the remote VTX power switch. With the XILO Stax flight controller, you are able to map a switch on your radio to turn on or off your VTX. This is useful when you are plugging in and don't want to broadcast video signal or you crashed your quad and want to prevent a roasted VTX. When a video transmitter isn't in flight it can quickly overheat due to lack of air flow, and this ability to control power can save you many burnt up VTXs.

The Stax uses standard 30.5x30.5 mounting hole configuration. The FC includes M3 silicone mounting grommets to reduce vibrations to your gyro, ensuring accurate readings.

Other features such as OSD, telemetry, multiple UARTs, 5V pads, SBUS and PPM support, all come standard with the XILO Stax Flight Controller.

Whether you are looking for a stack for a brand new build or just freshen up an older quad, the XILO Stax will get the job done, without breaking the bank.

XILO, affordability redefined.

UPDATE HISTORY

Version 1.1 update (Oct. 2019)

  • Spacing for receiver pins (XM+/Crossfire Nano) is now correct!
  • 16MB onboard flash for Blackbox

Version 1.2 update (March 2020)

  • Changed ICM20602 gyro to MPU6000 gyro for less sensitivity to noise and vibrations

NOTE: The newest version (board sold after Feb. 2020) of the XILO STAX FC with the MPU6000 Gyro have custom firmware  for this board with BF 4.1.3 pre-loaded. Do no flash anything before 4.1.5 on this FC or it will not work.

Software/Hardware Features

XILO Stax F4 Flight Controller

Features

  • 2-6S Direct Lipo input support (5-26v)
  • On-board BetaFlight OSD
  • VTX Remote Power switch
  • On-board 5v/2A and 3.3v/0.2A regulators
  • SBUS and PPM support
  • RGB LED dedicated pad
  • VBAT Monitoring support
  • 16MB Flash for Blackbox
  • 6x UART Ports
  • Betaflight support (Supports DSHOT protocol)
  • BLHeli pass-through flashing supported by hardware

Specifications

  • STM32F405 (2MB flash) 32-bit processor
  • MPU6000 Gyro/Accelerometer
  • High quality 1.6mm PCB
  • Micro USB connector for programming
  • Dimensions: 36x36x6mm (includes USB in height)
  • Mounting Holes: 30.5mm square to center of holes
  • Weight: 7g

User Manual & Firmware

Note: If you update the FC firmware the BlackBox feature may not be enabled anymore. You can re-enable it by adding this text to the CLI command line within Betaflight:

resource FLASH_CS 1 B02
resource SPI_PREINIT_IPU 2 B02
save

How to setup remote VTX power switch

The XILO Stax flight controller features a power pad for your video transmitter that can be remotely controlled via a switch setup in Betaflight. This allows you to remotely turn your VTX on or off from your radio! Simply solder your VTX to the corresponding pads on the Stax FC, (VTX, S/A, PWR, GND), the PWR pad will provide your VTX with filtered VBATT power. By default, the pad will be powered on. Go into Beta to set up a switch if you want to control power on/off remotely. You will find it under the "Modes" tab and "USER1" switch. Assign this to the AUX switch of your choice to turn the power on/off for that PWR pad. Easy!

Remote VTX Power Switch

Includes

  • XILO Stax F4 Flight Controller
  • 1x LC Power Filter
  • 1x 8pin Harness
  • 1x 8pin Extended Harness
  • 12x Silicone Grommets

Videos