Big brother to the VERT RACER, this low profile - stretched X - mid-mount - vertical arm design (developed by Bob Roogi) now carries a GoPro! Mount included.
Build at a Hyperlow 10mm with an AIO and ESC's on arms, or at 15mm with the included carbon spacers for a 4 in 1 + FC stack build. (SPEDIX 30A and Revolt is an effortless fit). Both sets of hardware included.
The 5mm carbon arm spacers used for a 15mm build even allow you to offset the front and rear prop planes by raising the rear arms for cleaner air, avoiding prop wash.
The frame maintains a slim body profile thanks to the strap plate borrowed from the UNIBODY series. This allows for dual straps use without compromising main plate integrity and adds a lateral battery mounting option. The battery is also cushioned by a custom neoprene pad, along with a smaller pad for the VTX antennas SMA
Mid-mount
Lowering the battery all the way into the prop plane gives the most neutral control possible. Motors do not have to work as hard to balance a higher CG, making for more fluid control and much smoother transitions. Fast acro maneuvers are effortless, and the acceptable tuning window is greatly increased. Feels just like a sim.
V2 UPDATES
- Press nut arm assembly
- Front and rear braces
- Easy access bottom plate
- Component mounting shelves
- V2 Hero+Session mount
- Subtle design tweaks
+ The V2 upgrade now matches the Vert Freestyles performance in the air with its serviceability on the bench. The undercarriage plate has been split into three sections allowing the center piece to be easily removed while leaving the arms in place.
+ Internal mounting shelves are now included in the kit. These designated mounting platforms provide room for components on top and wiring to run underneath helping keep a clean and secure build.
+ Arm braces are now included for optional rigidity and durability. The front braces are compatible with 15mm builds only.
+ The new GoPro mount also provides a custom fit for both the Session and the Hero GoPro models, all within the same low weight design.
(All parts backward compatible, although the V2 main body pressnuts have been moved from the bottom to top plate.)
Features
- Mid-mount 5" freestyle frame
- Vertical arms
- Stretched X
- 10mm + 15mm hardware
- GoPro Mount
- Double strap plate
- 3 Battery straps
- RX antenna mounts, straws and caps
- Battery and antenna pads
- Press nut assembly
- Offset rear prop plane
- Micro cam only - mounts included
- Frame weight: ~120g (15mm no braces)
Includes
Carbon
- 1 x 2mm top plate
- 3 x 2mm bottom plate
- 1 x 2mm camera bumper
- 1 x 2mm strap plate
- 4 x 5mm arm spacers (for 15mm build)
- 4 x 2mm locking tabs
- 4 x 5mm arms
- 4 x 5mm arm brace
FPV Mounts
- TPU micro cam mounting set
Session Mount
- 2 x TPU prints
- 2 x 20mm standoffs
- 4 x bolts
RX Antenna
- 2 horizontal mount
- straws + caps
Pads
- 1 x Battery pad
- 1 x Antenna pad
FC + Component Mounting
- 4 x 1mm nylon washers
- 4 x 5mm nylon standoffs
- 4 x nylon nuts
- TPU Shelves
Hardware
- 6 x 10mm standoffs
- 6 x 15mm standoffs
- 8 x 22mm bolts (for 15mm arms)
- 8 x 16mm bolts (for 10mm arms
- 4 x 14mm bolts (for arm to brace attachment)
- 4 x locknuts (for arm to brace attachment)
- 6 x 12mm bolts
- 6 x 10mm bolts
- 4 x 8mm
- 12 x nylon nuts
Straps
- 3 x Hyperlow Straps