Orders ship from the U.S.

Holybro Kakute V2 - Atlatl HV - Tekko32 4-in-1 ESC Combo
Holybro Kakute V2 - Atlatl HV - Tekko32 4-in-1 ESC Combo
Holybro Kakute V2 - Atlatl HV - Tekko32 4-in-1 ESC Combo
Holybro Kakute V2 - Atlatl HV - Tekko32 4-in-1 ESC Combo

Holybro Kakute V2 - Atlatl HV - Tekko32 4-in-1 ESC Combo

Regular price
Sold out
Sale price
$104.99
Shipping calculated at checkout.

Holybro is saving you time and guesswork into making your perfect FPV stack. Comes with the Kakute V2 FC, Atlatl HV vtx, and the Tekko32 4-in-1 ESC. This is the stack found in the Holybro Kopis 1 Racing Drone.

Tekko32 35A 4-in-1 ESC

Features

  • 4-in-1 ESC with 30.5x30.5mm mounting holes, supports DSHOT 1200, BLHELI32 firmware
  • Added more CAPS to reduce power noise
  • 32bit ESC with BLHELI32 firmware
  • 4PWM input
  • Voltage output (VBAT), ESC Telemetry(TELEM)
  • Supports Oneshot / Multishot / Dshot PWM
  • Supports damped light
  • NO BEC

Specifications

  • Supports 3-6S lipo input
  • 35A continuous current, 50A burst
  • Mounting holes 30.5x30.5mm
  • Size: 55*40*6.4mm
  • Weight: 17g

Kakute F4 V2

New V2 Features

  • Two extra UART Ports
  • UART4 port for serial camera like the runcam split. (This is not the same as Betaflight Camera Control, which runs of the OSD menu for cameras like the swift, monster).
  • UART5 port for ESC telemetry support (for BLheli32 and KISS)
  • Through-hole solder pads instead of flat pads for more secure soldering especially for beginners.
  • Barometer sensor on board allows altitude hold mode.
  • Dedicated I2C pads to connect extra peripherals (like an external compass)

Features

  • Supports Betaflight and Cleanflight.
  • Betaflight OSD. Change PIDs, adjust common configuration parameters, and change video transmitter channel and power level, all using your transmitter sticks and goggles.
  • Soft-mounting built in. The IMU ("gyro") chip on this board is mounted on vibration-isolating foam. This means that there is no need to soft-mount the board itself.
  • New high-performance / low-noise / high sensitivity IMU. ICM20689 with 6-axis gyro and accelerometer. Can run at up to 32 kHz.
  • 2 oz. copper PCB allows up to 120A maximum continuous current.
  • Dedicated bootloader button for easy firmware flashing.
  • Low-profile design fits into even very compact frames.
  • Input voltage 7v to 42v. Power the board directly from the flight pack, up to 6S (on "BAT" pad only).
  • Automatic voltage monitoring. No need to run a separate vBat wire for voltage monitoring; the Kakute F4 AIO monitors voltage directly from the battery power lead.
  • Filtered voltage output for clean, noise-free video. On-board regulators output 5v at up to 1.5 amps and 3.3v at up to 200 mA to power peripherals such as receiver, video transmitter, FPV camera, or LED strip.
  • Supports BLHeli pass-through for easy ESC upgrade and configuration.

Specifications

  • MCU: STM32F405RGT6 32-bit processor
  • IMU: ICM20689 (SPI)
  • Barometer: BMP280
  • USB VCP Driver (all UARTs usable simultaneously; USB does not take up a UART)
  • 5 hardware UARTS (UART1,3,4, 5, 6)
  • Supports serial receivers (SBUS, iBus, Spektrum, Crossfire) only. PPM and PWM receivers are not supported.
  • 128 Mbit Dataflash chip for Blackbox logging
  • Dimensions: 35x30x8mm (includes USB in height)
  • Mounting Holes: Standard 30.5mm square to center of holes
  • Weight: 7g

Atlatl HV

Features

  • Supports Betaflight and Cleanflight.
  • Betaflight OSD. Change PIDs, adjust common configuration parameters, and change video transmitter channel and power level, all using your transmitter sticks and goggles.
  • Soft-mounting built in. The IMU (“gyro”) chip on this board is mounted on vibration-isolating foam. This means that there is no need to soft-mount the board itself.
  • New high-performance / low-noise / high sensitivity IMU. ICM20689 with 6-axis gyro and accelerometer. Can run at up to 32 kHz.
  • 2 oz. copper PCB allows up to 120A maximum continuous current.
  • Dedicated bootloader button for easy firmware flashing.
  • Low-profile design fits into even very compact frames.
  • Input voltage 7v to 42v. Power the board directly from the flight pack, up to 6S (on “BAT” pad only).
  • Automatic voltage monitoring. No need to run a separate vBat wire for voltage monitoring; the Kakute F4 AIO monitors voltage directly from the battery power lead.
  • Filtered voltage output for clean, noise-free video. On-board regulators output 5v at up to 1.5 amps and 3.3v at up to 200 mA to power peripherals such as receiver, video transmitter, FPV camera, or LED strip.
  • Supports BLHeli pass-through for easy ESC upgrade and configuration.

Specifications

  • MCU: STM32F405RGT6 32-bit processor
  • IMU: ICM20689 (SPI)
  • USB VCP Driver (all UARTs usable simultaneously; USB does not take up a UART)
  • 3 hardware UARTS (UART1,3,6)
  • 128 Mbit Dataflash chip for Blackbox logging
  • Dimensions: 35x43x7mm (includes USB in height)
  • Mounting Holes: Standard 30.5mm square to center of holes 
  • Weight: 7g

Includes

  • 1x Tekko32 35A 4-in-1 ESC
  • 1x Kakute F4 V2 Flight Controller
  • 1x Atlatl HV Video Transmitter

Resources